What killed these X2 caps?iPhone programmable capswhat is the value of these capacitors?What are these capacitors?What is the difference between these circuit?what frequencies do caps filter?What are these electrolytic capacitors?Replace foil caps with ceramic caps?Dimensioning smoothing capacitor for China DIY LED lampWhat is the type of these caps?Are these circuits equivalents (caps in parallel with VCC)
Is there a hemisphere-neutral way of specifying a season?
Which is the best way to check return result?
Alternative to sending password over mail?
What exploit Are these user agents trying to use?
How to add frame around section using titlesec?
Unable to supress ligatures in headings which are set in Caps
iPad being using in wall mount battery swollen
What reasons are there for a Capitalist to oppose a 100% inheritance tax?
Am I breaking OOP practice with this architecture?
Venezuelan girlfriend wants to travel the USA to be with me. What is the process?
What method can I use to design a dungeon difficult enough that the PCs can't make it through without killing them?
How to show a landlord what we have in savings?
What about the virus in 12 Monkeys?
Why can't we play rap on piano?
Is "remove commented out code" correct English?
One verb to replace 'be a member of' a club
How seriously should I take size and weight limits of hand luggage?
Assassin's bullet with mercury
In 'Revenger,' what does 'cove' come from?
Is it acceptable for a professor to tell male students to not think that they are smarter than female students?
Personal Teleportation: From Rags to Riches
How can saying a song's name be a copyright violation?
Different meanings of こわい
What is the idiomatic way to say "clothing fits"?
What killed these X2 caps?
iPhone programmable capswhat is the value of these capacitors?What are these capacitors?What is the difference between these circuit?what frequencies do caps filter?What are these electrolytic capacitors?Replace foil caps with ceramic caps?Dimensioning smoothing capacitor for China DIY LED lampWhat is the type of these caps?Are these circuits equivalents (caps in parallel with VCC)
$begingroup$
A few years ago, I designed an MCU-controlled dimmer driving a 150W mains halogen lamp. This is in Western Europe; 50Hz 230VAC. It uses X2-rated capacitors as capacitive droppers for the power supply, and another X2-rated capacitor for interference suppression:
The dimmer has gradually started misbehaving, and on debugging I found that all of the X2 caps have died (meaning they have less than 10% of their rated capacitance remaining):
The caps in the picture:
C1, capacitive dropper, should be 100nF, measures 6.4nF
C2, capacitive dropper, should be 100nF, measures 6.9nF
C5, interference suppression, should be 100nF, measures 1.4nF
Cnew, fresh cap not from circuit, measures 93nF
All of them measure open circuit (>40MΩ) on resistance.
C1, C2, and Cnew are labeled MEX/TENTA MKP 0.1µF K X2 275VAC 40/100/21 [approval logos] EN 60384-14 01-14 250VAC; 275VAC nominal rated (significantly higher withstanding voltage, datasheet here). They are all from the same batch, bought in Sep 2016. I suspect 01-14 is a date code, so they'd be from early 2014.
C5 is from the same brand; it has virtually the same markings (except EN 132400), but is physically larger. I got it as part of some Velleman kit years ago, where it was also used as a suppression cap. No datasheet.
What caused these caps to lose their capacitance?
- Is this deterioration normal behaviour for X2 caps? The dimmer saw a lot of use, being powered for an estimated 7000 hours.
- Should I have derated the caps more? I agree 230VAC is pretty close to 275VAC, but as I understand it that is their nominal rating, and they should be able to handle transients way above that. Also, 275VAC seems by far the most common rating available on Digikey and the like.
- Am I using the capacitors wrong somehow?
- Are these capacitors from a bad brand/series/batch?
capacitor mains x-capacitor
asked 1 hour ago
marcelmmarcelm
1,3721716
$endgroup$
add a comment |
$begingroup$
A few years ago, I designed an MCU-controlled dimmer driving a 150W mains halogen lamp. This is in Western Europe; 50Hz 230VAC. It uses X2-rated capacitors as capacitive droppers for the power supply, and another X2-rated capacitor for interference suppression:
The dimmer has gradually started misbehaving, and on debugging I found that all of the X2 caps have died (meaning they have less than 10% of their rated capacitance remaining):
The caps in the picture:
C1, capacitive dropper, should be 100nF, measures 6.4nF
C2, capacitive dropper, should be 100nF, measures 6.9nF
C5, interference suppression, should be 100nF, measures 1.4nF
Cnew, fresh cap not from circuit, measures 93nF
All of them measure open circuit (>40MΩ) on resistance.
C1, C2, and Cnew are labeled MEX/TENTA MKP 0.1µF K X2 275VAC 40/100/21 [approval logos] EN 60384-14 01-14 250VAC; 275VAC nominal rated (significantly higher withstanding voltage, datasheet here). They are all from the same batch, bought in Sep 2016. I suspect 01-14 is a date code, so they'd be from early 2014.
C5 is from the same brand; it has virtually the same markings (except EN 132400), but is physically larger. I got it as part of some Velleman kit years ago, where it was also used as a suppression cap. No datasheet.
What caused these caps to lose their capacitance?
- Is this deterioration normal behaviour for X2 caps? The dimmer saw a lot of use, being powered for an estimated 7000 hours.
- Should I have derated the caps more? I agree 230VAC is pretty close to 275VAC, but as I understand it that is their nominal rating, and they should be able to handle transients way above that. Also, 275VAC seems by far the most common rating available on Digikey and the like.
- Am I using the capacitors wrong somehow?
- Are these capacitors from a bad brand/series/batch?
capacitor mains x-capacitor
asked 1 hour ago
marcelmmarcelm
1,3721716
$endgroup$
1
$begingroup$
Western Europe is 50 Hz, not 60 Hz.
$endgroup$
– Transistor
29 mins ago
$begingroup$
@Transistor Of course! I'm not sure what I was thinking when I typed 60Hz... Thanks and fixed!
$endgroup$
– marcelm
15 mins ago
add a comment |
$begingroup$
A few years ago, I designed an MCU-controlled dimmer driving a 150W mains halogen lamp. This is in Western Europe; 50Hz 230VAC. It uses X2-rated capacitors as capacitive droppers for the power supply, and another X2-rated capacitor for interference suppression:
The dimmer has gradually started misbehaving, and on debugging I found that all of the X2 caps have died (meaning they have less than 10% of their rated capacitance remaining):
The caps in the picture:
C1, capacitive dropper, should be 100nF, measures 6.4nF
C2, capacitive dropper, should be 100nF, measures 6.9nF
C5, interference suppression, should be 100nF, measures 1.4nF
Cnew, fresh cap not from circuit, measures 93nF
All of them measure open circuit (>40MΩ) on resistance.
C1, C2, and Cnew are labeled MEX/TENTA MKP 0.1µF K X2 275VAC 40/100/21 [approval logos] EN 60384-14 01-14 250VAC; 275VAC nominal rated (significantly higher withstanding voltage, datasheet here). They are all from the same batch, bought in Sep 2016. I suspect 01-14 is a date code, so they'd be from early 2014.
C5 is from the same brand; it has virtually the same markings (except EN 132400), but is physically larger. I got it as part of some Velleman kit years ago, where it was also used as a suppression cap. No datasheet.
What caused these caps to lose their capacitance?
- Is this deterioration normal behaviour for X2 caps? The dimmer saw a lot of use, being powered for an estimated 7000 hours.
- Should I have derated the caps more? I agree 230VAC is pretty close to 275VAC, but as I understand it that is their nominal rating, and they should be able to handle transients way above that. Also, 275VAC seems by far the most common rating available on Digikey and the like.
- Am I using the capacitors wrong somehow?
- Are these capacitors from a bad brand/series/batch?
capacitor mains x-capacitor
asked 1 hour ago
marcelmmarcelm
1,3721716
$endgroup$
A few years ago, I designed an MCU-controlled dimmer driving a 150W mains halogen lamp. This is in Western Europe; 50Hz 230VAC. It uses X2-rated capacitors as capacitive droppers for the power supply, and another X2-rated capacitor for interference suppression:
The dimmer has gradually started misbehaving, and on debugging I found that all of the X2 caps have died (meaning they have less than 10% of their rated capacitance remaining):
The caps in the picture:
C1, capacitive dropper, should be 100nF, measures 6.4nF
C2, capacitive dropper, should be 100nF, measures 6.9nF
C5, interference suppression, should be 100nF, measures 1.4nF
Cnew, fresh cap not from circuit, measures 93nF
All of them measure open circuit (>40MΩ) on resistance.
C1, C2, and Cnew are labeled MEX/TENTA MKP 0.1µF K X2 275VAC 40/100/21 [approval logos] EN 60384-14 01-14 250VAC; 275VAC nominal rated (significantly higher withstanding voltage, datasheet here). They are all from the same batch, bought in Sep 2016. I suspect 01-14 is a date code, so they'd be from early 2014.
C5 is from the same brand; it has virtually the same markings (except EN 132400), but is physically larger. I got it as part of some Velleman kit years ago, where it was also used as a suppression cap. No datasheet.
What caused these caps to lose their capacitance?
- Is this deterioration normal behaviour for X2 caps? The dimmer saw a lot of use, being powered for an estimated 7000 hours.
- Should I have derated the caps more? I agree 230VAC is pretty close to 275VAC, but as I understand it that is their nominal rating, and they should be able to handle transients way above that. Also, 275VAC seems by far the most common rating available on Digikey and the like.
- Am I using the capacitors wrong somehow?
- Are these capacitors from a bad brand/series/batch?
capacitor mains x-capacitor
capacitor mains x-capacitor
asked 1 hour ago
marcelmmarcelm
1,3721716
asked 1 hour ago
marcelmmarcelm
1,3721716
edited 16 mins ago
marcelm
asked 1 hour ago
marcelmmarcelm
1,3721716
asked 1 hour ago
marcelmmarcelm
1,3721716
asked 1 hour ago
marcelmmarcelm
1,3721716
1,3721716
1
$begingroup$
Western Europe is 50 Hz, not 60 Hz.
$endgroup$
– Transistor
29 mins ago
$begingroup$
@Transistor Of course! I'm not sure what I was thinking when I typed 60Hz... Thanks and fixed!
$endgroup$
– marcelm
15 mins ago
add a comment |
1
$begingroup$
Western Europe is 50 Hz, not 60 Hz.
$endgroup$
– Transistor
29 mins ago
$begingroup$
@Transistor Of course! I'm not sure what I was thinking when I typed 60Hz... Thanks and fixed!
$endgroup$
– marcelm
15 mins ago
1
1
$begingroup$
Western Europe is 50 Hz, not 60 Hz.
$endgroup$
– Transistor
29 mins ago
$begingroup$
Western Europe is 50 Hz, not 60 Hz.
$endgroup$
– Transistor
29 mins ago
$begingroup$
@Transistor Of course! I'm not sure what I was thinking when I typed 60Hz... Thanks and fixed!
$endgroup$
– marcelm
15 mins ago
$begingroup$
@Transistor Of course! I'm not sure what I was thinking when I typed 60Hz... Thanks and fixed!
$endgroup$
– marcelm
15 mins ago
add a comment |
1 Answer
1
active
oldest
votes
$begingroup$
The film capacitors are made to be "self healing" which just means that when they develop a short due to abuse the area around the short gets blown away, reducing the capacitance.
It appears your application has frequent transients either from within or without that exceed the design capability of the capacitors. You can try to track them down at the source, attempt to shunt them with something like a bipolar TVS across the caps, or buy better (higher voltage rated) capacitors.
answered 58 mins ago
Spehro PefhanySpehro Pefhany
212k5162428
$endgroup$
add a comment |
Your Answer
StackExchange.ifUsing("editor", function ()
return StackExchange.using("mathjaxEditing", function ()
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
);
);
, "mathjax-editing");
StackExchange.ifUsing("editor", function ()
return StackExchange.using("schematics", function ()
StackExchange.schematics.init();
);
, "cicuitlab");
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "135"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f430568%2fwhat-killed-these-x2-caps%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
The film capacitors are made to be "self healing" which just means that when they develop a short due to abuse the area around the short gets blown away, reducing the capacitance.
It appears your application has frequent transients either from within or without that exceed the design capability of the capacitors. You can try to track them down at the source, attempt to shunt them with something like a bipolar TVS across the caps, or buy better (higher voltage rated) capacitors.
answered 58 mins ago
Spehro PefhanySpehro Pefhany
212k5162428
$endgroup$
add a comment |
$begingroup$
The film capacitors are made to be "self healing" which just means that when they develop a short due to abuse the area around the short gets blown away, reducing the capacitance.
It appears your application has frequent transients either from within or without that exceed the design capability of the capacitors. You can try to track them down at the source, attempt to shunt them with something like a bipolar TVS across the caps, or buy better (higher voltage rated) capacitors.
answered 58 mins ago
Spehro PefhanySpehro Pefhany
212k5162428
$endgroup$
add a comment |
$begingroup$
The film capacitors are made to be "self healing" which just means that when they develop a short due to abuse the area around the short gets blown away, reducing the capacitance.
It appears your application has frequent transients either from within or without that exceed the design capability of the capacitors. You can try to track them down at the source, attempt to shunt them with something like a bipolar TVS across the caps, or buy better (higher voltage rated) capacitors.
answered 58 mins ago
Spehro PefhanySpehro Pefhany
212k5162428
$endgroup$
The film capacitors are made to be "self healing" which just means that when they develop a short due to abuse the area around the short gets blown away, reducing the capacitance.
It appears your application has frequent transients either from within or without that exceed the design capability of the capacitors. You can try to track them down at the source, attempt to shunt them with something like a bipolar TVS across the caps, or buy better (higher voltage rated) capacitors.
answered 58 mins ago
Spehro PefhanySpehro Pefhany
212k5162428
answered 58 mins ago
Spehro PefhanySpehro Pefhany
212k5162428
answered 58 mins ago
Spehro PefhanySpehro Pefhany
212k5162428
answered 58 mins ago
Spehro PefhanySpehro Pefhany
212k5162428
212k5162428
add a comment |
add a comment |
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f430568%2fwhat-killed-these-x2-caps%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
1
$begingroup$
Western Europe is 50 Hz, not 60 Hz.
$endgroup$
– Transistor
29 mins ago
$begingroup$
@Transistor Of course! I'm not sure what I was thinking when I typed 60Hz... Thanks and fixed!
$endgroup$
– marcelm
15 mins ago