Why would a switch ever send an ARP request for a MAC address when it can just wait for the first packet to be received from a device?Won't GLBP confuse a switch's mac address-table?What happens if two hosts with the same MAC address are in the same broadcast domain?How does a switch learn a switch table?Learn MAC addresses via replies to other hosts requestsSwitch learning MAC address of default routerWhat is the difference between ARP and BUM Traffic?ARP broadcast vs Default RouteWhy does the receiver of an ARP request updates its cache tableHow does a router know the destination mac?How does a system know the local gateways MAC address for given IP address
what does a native speaker say when he wanted to leave his work?
Is there any good reason to write "it is easy to see"?
Tikzpicture in figure problem
How do employ ' ("prime") in math mode at the correct depth?
Rounding a number extracted by jq to limit the decimal points
Solubility in different pressure conditions
Program which behaves differently in/out of a debugger
CPLD based Pierce oscillator
Non-deterministic Finite Automata | Sipser Example 1.16
Anatomically Correct Carnivorous Tree
Smallest Guaranteed hash collision cycle length
How exactly does artificial gravity work?
Wireless headphones interfere with Wi-Fi signal on laptop
declared variable inside void setup is forgotten in void loop
Can a tourist shoot a gun in the USA?
Where to find every-day healthy food near Heathrow Airport?
What makes "quality" analog AV cables better than cheap cables?
How do I tell my supervisor that he is choosing poor replacements for me while I am on maternity leave?
Why is a set not a partition of itself?
Could there be a material that inverts the colours seen through it?
Find hamming distance between two Strings of equal length in Java
Jumping frame contents with beamer and pgfplots
Is there ever any indication in the MCU as to how Spider-Man got his powers?
Do Life Drain attacks from wights stack?
Why would a switch ever send an ARP request for a MAC address when it can just wait for the first packet to be received from a device?
Won't GLBP confuse a switch's mac address-table?What happens if two hosts with the same MAC address are in the same broadcast domain?How does a switch learn a switch table?Learn MAC addresses via replies to other hosts requestsSwitch learning MAC address of default routerWhat is the difference between ARP and BUM Traffic?ARP broadcast vs Default RouteWhy does the receiver of an ARP request updates its cache tableHow does a router know the destination mac?How does a system know the local gateways MAC address for given IP address
I've been reading 'Windows Networking Fundamentals' and in that book it says that a switch can learn what MAC address is associated with a particular port when the connected device makes its first transmission to the switch by checking the source of the packet. It goes on to say that if the packet destination is an unknown MAC address it will flood every port with the packet (except the port it received the packet from), and then can potentially use the reply from the destination device to learn the destination MAC address.
However, in my Networks lectures, I have been told that switches send an ARP request to any unknown devices when they are first connected and the ARP reply is used to obtain the MAC address.
If the switch does send an ARP request when devices are first connected, why would any of the first method ever need to occur?
So does the switch initiate the process of obtaining a MAC address? Or does the switch learn it after the device makes its first transmission to the switch? Or does it depend on some other factors?
switch mac-address switching arp
asked 5 hours ago
CutterCutter
83
New contributor
Cutter is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I've been reading 'Windows Networking Fundamentals' and in that book it says that a switch can learn what MAC address is associated with a particular port when the connected device makes its first transmission to the switch by checking the source of the packet. It goes on to say that if the packet destination is an unknown MAC address it will flood every port with the packet (except the port it received the packet from), and then can potentially use the reply from the destination device to learn the destination MAC address.
However, in my Networks lectures, I have been told that switches send an ARP request to any unknown devices when they are first connected and the ARP reply is used to obtain the MAC address.
If the switch does send an ARP request when devices are first connected, why would any of the first method ever need to occur?
So does the switch initiate the process of obtaining a MAC address? Or does the switch learn it after the device makes its first transmission to the switch? Or does it depend on some other factors?
switch mac-address switching arp
asked 5 hours ago
CutterCutter
83
New contributor
Cutter is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I've been reading 'Windows Networking Fundamentals' and in that book it says that a switch can learn what MAC address is associated with a particular port when the connected device makes its first transmission to the switch by checking the source of the packet. It goes on to say that if the packet destination is an unknown MAC address it will flood every port with the packet (except the port it received the packet from), and then can potentially use the reply from the destination device to learn the destination MAC address.
However, in my Networks lectures, I have been told that switches send an ARP request to any unknown devices when they are first connected and the ARP reply is used to obtain the MAC address.
If the switch does send an ARP request when devices are first connected, why would any of the first method ever need to occur?
So does the switch initiate the process of obtaining a MAC address? Or does the switch learn it after the device makes its first transmission to the switch? Or does it depend on some other factors?
switch mac-address switching arp
asked 5 hours ago
CutterCutter
83
New contributor
Cutter is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I've been reading 'Windows Networking Fundamentals' and in that book it says that a switch can learn what MAC address is associated with a particular port when the connected device makes its first transmission to the switch by checking the source of the packet. It goes on to say that if the packet destination is an unknown MAC address it will flood every port with the packet (except the port it received the packet from), and then can potentially use the reply from the destination device to learn the destination MAC address.
However, in my Networks lectures, I have been told that switches send an ARP request to any unknown devices when they are first connected and the ARP reply is used to obtain the MAC address.
If the switch does send an ARP request when devices are first connected, why would any of the first method ever need to occur?
So does the switch initiate the process of obtaining a MAC address? Or does the switch learn it after the device makes its first transmission to the switch? Or does it depend on some other factors?
switch mac-address switching arp
switch mac-address switching arp
asked 5 hours ago
CutterCutter
83
New contributor
Cutter is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 5 hours ago
CutterCutter
83
New contributor
Cutter is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 5 hours ago
CutterCutter
83
New contributor
Cutter is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 5 hours ago
CutterCutter
83
asked 5 hours ago
CutterCutter
83
83
New contributor
Cutter is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
Cutter is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
add a comment |
1 Answer
1
active
oldest
votes
You are confusing switching, where a switch creates and updates a MAC address table as frames pass through it, with the switch management.
Switching is a layer-2 function, and a dumb switch will never use ARP. ARP is used by layer-3 devices to relate a layer-3 address to a layer-2 address, something that is not done for simple layer-2 switching.
A managed switch will have a layer-3 management interface that acts like a host on the LAN, so that interface (virtual host) needs to use ARP to relate layer-3 addresses to layer-2 addresses for any layer-3 packets that the switch management interface needs to send to another device. That has nothing to do with the switching function of the switch.
answered 5 hours ago
Ron Maupin♦Ron Maupin
70.2k1371130
So a layer 2 switch will never use ARP and a layer 3 switch will always use ARP?
– Cutter
5 hours ago
That's not at all what I said. A managed layer-2 switch will use ARP for its management interface because that is a layer-3 interface, but it has nothing to do with switching frames. A layer-3 switch is always a manged switch, but not all managed switches are layer-3 switches. Also, a layer-3 switch is still a layer-2 switch, and the layer-2 switching uses a MAC address table, like any other layer-2 switch. The layer-3 part is a routing module in the switch, and it uses ARP the same way a router does.
– Ron Maupin♦
4 hours ago
Okay sorry, one more question. So if the layer-2 part of a layer-3 switch uses a MAC address table, why does the layer-3 part need to use ARP? Doesn't it already have the MAC address from the MAC address table used in layer-2?
– Cutter
4 hours ago
MAC address tables relate a MAC address to a switch interface, and that is completely different than what ARP does, which is to relate a layer-3 address to a layer-2 address. Switching doesn't know anything about layer-3, and that allows a switch to carry any layer-3 protocol. The layer-2 and layer-3 functions in a layer-3 switch are completely separate. It is really just putting a router and a switch in the same box. The functions are very different.
– Ron Maupin♦
4 hours ago
Okay thank you.
– Cutter
4 hours ago
add a comment |
Your Answer
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "496"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
Cutter is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fnetworkengineering.stackexchange.com%2fquestions%2f59088%2fwhy-would-a-switch-ever-send-an-arp-request-for-a-mac-address-when-it-can-just-w%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
You are confusing switching, where a switch creates and updates a MAC address table as frames pass through it, with the switch management.
Switching is a layer-2 function, and a dumb switch will never use ARP. ARP is used by layer-3 devices to relate a layer-3 address to a layer-2 address, something that is not done for simple layer-2 switching.
A managed switch will have a layer-3 management interface that acts like a host on the LAN, so that interface (virtual host) needs to use ARP to relate layer-3 addresses to layer-2 addresses for any layer-3 packets that the switch management interface needs to send to another device. That has nothing to do with the switching function of the switch.
answered 5 hours ago
Ron Maupin♦Ron Maupin
70.2k1371130
So a layer 2 switch will never use ARP and a layer 3 switch will always use ARP?
– Cutter
5 hours ago
That's not at all what I said. A managed layer-2 switch will use ARP for its management interface because that is a layer-3 interface, but it has nothing to do with switching frames. A layer-3 switch is always a manged switch, but not all managed switches are layer-3 switches. Also, a layer-3 switch is still a layer-2 switch, and the layer-2 switching uses a MAC address table, like any other layer-2 switch. The layer-3 part is a routing module in the switch, and it uses ARP the same way a router does.
– Ron Maupin♦
4 hours ago
Okay sorry, one more question. So if the layer-2 part of a layer-3 switch uses a MAC address table, why does the layer-3 part need to use ARP? Doesn't it already have the MAC address from the MAC address table used in layer-2?
– Cutter
4 hours ago
MAC address tables relate a MAC address to a switch interface, and that is completely different than what ARP does, which is to relate a layer-3 address to a layer-2 address. Switching doesn't know anything about layer-3, and that allows a switch to carry any layer-3 protocol. The layer-2 and layer-3 functions in a layer-3 switch are completely separate. It is really just putting a router and a switch in the same box. The functions are very different.
– Ron Maupin♦
4 hours ago
Okay thank you.
– Cutter
4 hours ago
add a comment |
You are confusing switching, where a switch creates and updates a MAC address table as frames pass through it, with the switch management.
Switching is a layer-2 function, and a dumb switch will never use ARP. ARP is used by layer-3 devices to relate a layer-3 address to a layer-2 address, something that is not done for simple layer-2 switching.
A managed switch will have a layer-3 management interface that acts like a host on the LAN, so that interface (virtual host) needs to use ARP to relate layer-3 addresses to layer-2 addresses for any layer-3 packets that the switch management interface needs to send to another device. That has nothing to do with the switching function of the switch.
answered 5 hours ago
Ron Maupin♦Ron Maupin
70.2k1371130
So a layer 2 switch will never use ARP and a layer 3 switch will always use ARP?
– Cutter
5 hours ago
That's not at all what I said. A managed layer-2 switch will use ARP for its management interface because that is a layer-3 interface, but it has nothing to do with switching frames. A layer-3 switch is always a manged switch, but not all managed switches are layer-3 switches. Also, a layer-3 switch is still a layer-2 switch, and the layer-2 switching uses a MAC address table, like any other layer-2 switch. The layer-3 part is a routing module in the switch, and it uses ARP the same way a router does.
– Ron Maupin♦
4 hours ago
Okay sorry, one more question. So if the layer-2 part of a layer-3 switch uses a MAC address table, why does the layer-3 part need to use ARP? Doesn't it already have the MAC address from the MAC address table used in layer-2?
– Cutter
4 hours ago
MAC address tables relate a MAC address to a switch interface, and that is completely different than what ARP does, which is to relate a layer-3 address to a layer-2 address. Switching doesn't know anything about layer-3, and that allows a switch to carry any layer-3 protocol. The layer-2 and layer-3 functions in a layer-3 switch are completely separate. It is really just putting a router and a switch in the same box. The functions are very different.
– Ron Maupin♦
4 hours ago
Okay thank you.
– Cutter
4 hours ago
add a comment |
You are confusing switching, where a switch creates and updates a MAC address table as frames pass through it, with the switch management.
Switching is a layer-2 function, and a dumb switch will never use ARP. ARP is used by layer-3 devices to relate a layer-3 address to a layer-2 address, something that is not done for simple layer-2 switching.
A managed switch will have a layer-3 management interface that acts like a host on the LAN, so that interface (virtual host) needs to use ARP to relate layer-3 addresses to layer-2 addresses for any layer-3 packets that the switch management interface needs to send to another device. That has nothing to do with the switching function of the switch.
answered 5 hours ago
Ron Maupin♦Ron Maupin
70.2k1371130
You are confusing switching, where a switch creates and updates a MAC address table as frames pass through it, with the switch management.
Switching is a layer-2 function, and a dumb switch will never use ARP. ARP is used by layer-3 devices to relate a layer-3 address to a layer-2 address, something that is not done for simple layer-2 switching.
A managed switch will have a layer-3 management interface that acts like a host on the LAN, so that interface (virtual host) needs to use ARP to relate layer-3 addresses to layer-2 addresses for any layer-3 packets that the switch management interface needs to send to another device. That has nothing to do with the switching function of the switch.
answered 5 hours ago
Ron Maupin♦Ron Maupin
70.2k1371130
answered 5 hours ago
Ron Maupin♦Ron Maupin
70.2k1371130
answered 5 hours ago
Ron Maupin♦Ron Maupin
70.2k1371130
answered 5 hours ago
Ron Maupin♦Ron Maupin
70.2k1371130
70.2k1371130
So a layer 2 switch will never use ARP and a layer 3 switch will always use ARP?
– Cutter
5 hours ago
That's not at all what I said. A managed layer-2 switch will use ARP for its management interface because that is a layer-3 interface, but it has nothing to do with switching frames. A layer-3 switch is always a manged switch, but not all managed switches are layer-3 switches. Also, a layer-3 switch is still a layer-2 switch, and the layer-2 switching uses a MAC address table, like any other layer-2 switch. The layer-3 part is a routing module in the switch, and it uses ARP the same way a router does.
– Ron Maupin♦
4 hours ago
Okay sorry, one more question. So if the layer-2 part of a layer-3 switch uses a MAC address table, why does the layer-3 part need to use ARP? Doesn't it already have the MAC address from the MAC address table used in layer-2?
– Cutter
4 hours ago
MAC address tables relate a MAC address to a switch interface, and that is completely different than what ARP does, which is to relate a layer-3 address to a layer-2 address. Switching doesn't know anything about layer-3, and that allows a switch to carry any layer-3 protocol. The layer-2 and layer-3 functions in a layer-3 switch are completely separate. It is really just putting a router and a switch in the same box. The functions are very different.
– Ron Maupin♦
4 hours ago
Okay thank you.
– Cutter
4 hours ago
add a comment |
So a layer 2 switch will never use ARP and a layer 3 switch will always use ARP?
– Cutter
5 hours ago
That's not at all what I said. A managed layer-2 switch will use ARP for its management interface because that is a layer-3 interface, but it has nothing to do with switching frames. A layer-3 switch is always a manged switch, but not all managed switches are layer-3 switches. Also, a layer-3 switch is still a layer-2 switch, and the layer-2 switching uses a MAC address table, like any other layer-2 switch. The layer-3 part is a routing module in the switch, and it uses ARP the same way a router does.
– Ron Maupin♦
4 hours ago
Okay sorry, one more question. So if the layer-2 part of a layer-3 switch uses a MAC address table, why does the layer-3 part need to use ARP? Doesn't it already have the MAC address from the MAC address table used in layer-2?
– Cutter
4 hours ago
MAC address tables relate a MAC address to a switch interface, and that is completely different than what ARP does, which is to relate a layer-3 address to a layer-2 address. Switching doesn't know anything about layer-3, and that allows a switch to carry any layer-3 protocol. The layer-2 and layer-3 functions in a layer-3 switch are completely separate. It is really just putting a router and a switch in the same box. The functions are very different.
– Ron Maupin♦
4 hours ago
Okay thank you.
– Cutter
4 hours ago
So a layer 2 switch will never use ARP and a layer 3 switch will always use ARP?
– Cutter
5 hours ago
So a layer 2 switch will never use ARP and a layer 3 switch will always use ARP?
– Cutter
5 hours ago
That's not at all what I said. A managed layer-2 switch will use ARP for its management interface because that is a layer-3 interface, but it has nothing to do with switching frames. A layer-3 switch is always a manged switch, but not all managed switches are layer-3 switches. Also, a layer-3 switch is still a layer-2 switch, and the layer-2 switching uses a MAC address table, like any other layer-2 switch. The layer-3 part is a routing module in the switch, and it uses ARP the same way a router does.
– Ron Maupin♦
4 hours ago
That's not at all what I said. A managed layer-2 switch will use ARP for its management interface because that is a layer-3 interface, but it has nothing to do with switching frames. A layer-3 switch is always a manged switch, but not all managed switches are layer-3 switches. Also, a layer-3 switch is still a layer-2 switch, and the layer-2 switching uses a MAC address table, like any other layer-2 switch. The layer-3 part is a routing module in the switch, and it uses ARP the same way a router does.
– Ron Maupin♦
4 hours ago
Okay sorry, one more question. So if the layer-2 part of a layer-3 switch uses a MAC address table, why does the layer-3 part need to use ARP? Doesn't it already have the MAC address from the MAC address table used in layer-2?
– Cutter
4 hours ago
Okay sorry, one more question. So if the layer-2 part of a layer-3 switch uses a MAC address table, why does the layer-3 part need to use ARP? Doesn't it already have the MAC address from the MAC address table used in layer-2?
– Cutter
4 hours ago
MAC address tables relate a MAC address to a switch interface, and that is completely different than what ARP does, which is to relate a layer-3 address to a layer-2 address. Switching doesn't know anything about layer-3, and that allows a switch to carry any layer-3 protocol. The layer-2 and layer-3 functions in a layer-3 switch are completely separate. It is really just putting a router and a switch in the same box. The functions are very different.
– Ron Maupin♦
4 hours ago
MAC address tables relate a MAC address to a switch interface, and that is completely different than what ARP does, which is to relate a layer-3 address to a layer-2 address. Switching doesn't know anything about layer-3, and that allows a switch to carry any layer-3 protocol. The layer-2 and layer-3 functions in a layer-3 switch are completely separate. It is really just putting a router and a switch in the same box. The functions are very different.
– Ron Maupin♦
4 hours ago
Okay thank you.
– Cutter
4 hours ago
Okay thank you.
– Cutter
4 hours ago
add a comment |
Cutter is a new contributor. Be nice, and check out our Code of Conduct.
Cutter is a new contributor. Be nice, and check out our Code of Conduct.
Cutter is a new contributor. Be nice, and check out our Code of Conduct.
Cutter is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Network Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fnetworkengineering.stackexchange.com%2fquestions%2f59088%2fwhy-would-a-switch-ever-send-an-arp-request-for-a-mac-address-when-it-can-just-w%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
